Breville Water Dispenser BWC200 User Manual

the Chill Control™  
Instruction Booklet  
Breville Customer Service Centre  
Australian Customers  
New Zealand Customers  
Mail: PO Box 22  
Botany, NSW, 2019  
AUSTRALIA  
Mail: Private Bag 94411  
Botany Manukau 2163  
Auckland NEW ZEALAND  
Phone: 1300 139 798  
Phone: 0800 273 845  
Fax:  
(02) 9384 9601  
Fax:  
0800 288 513  
Email: Customer Service:  
Email: Customer Service:  
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.  
Copyright Breville Pty. Ltd. 2012.  
Due to continued product improvement, the products illustrated/photographed  
in this booklet may vary slightly from the actual product.  
BWC200 Issue - E12  
BWC200  
 
BREvILLE RECOMMENdS SAFETy FIRST  
BREvILLE RECOMMENdS SAFETy FIRST  
At Breville we are very safety conscious. We design and manufacture consumer products with  
the safety of you, our valued customer foremost in mind. In addition we ask that you exercise  
a degree of care when using any electrical appliance and adhere to the following precautions.  
IMPORTANT SAFEGUARdS FOR BREvILLE ASSIST™ PLUG  
ALL ELECTRICAL APPLIANCES  
The Breville Chill Control™ comes with a  
unique Assist™ Plug, conveniently designed  
with a finger hole in the power plug for easy  
and safe removal from the wall outlet.  
This appliance is for household use only.  
Unwind power cord fully before use.  
Do not let power cord hang over the  
edge of a table or counter, or touch  
hot surfaces.  
Do not use the appliance for anything  
other than its intended purpose as  
described in this instruction book.  
Do not use outdoors. Do not use in  
moving vehicles or boats.  
IMPORTANT SAFEGUARdS  
For safety reasons it is recommended you  
plug your Breville Chill Control™ directly  
into its own electrical outlet on a dedicated  
circuit separate from other appliances. If the  
electrical circuit is overloaded with other  
appliances, your appliance may not function  
properly. Using in conjunction with a power  
strip or extension cord is not recommended.  
assembling and when storing the  
REAd ALL INSTRUCTIONS  
appliance.  
BEFORE USE ANd SAvE FOR  
The Breville Chill Control™ is not  
intended for use by young children or  
infirm persons unless they have been  
adequately supervised by a responsible  
person to ensure they can use the  
appliance safely.  
FUTURE REFERENCE  
Carefully read all instructions before  
operation and save for future reference.  
Close supervision is necessary when any  
appliance is used by or near children.  
Remove and safely discard any  
packaging material and promotional  
labels before using the Breville  
Chill Control™ for the first time.  
Regularly inspect the supply cord, plug  
and actual appliance for any damage.  
Do not operate if damaged in any way  
or after the appliance malfunctions.  
Immediately cease use of the appliance  
and call Breville Customer Service on  
ph: 1300 139 798 (Australia) or  
The Breville Chill Control™ has been  
designed specifically for the purpose  
of filtering and chilling water and must  
only be used with municipally treated  
water. Do not attempt to filter untreated,  
raw water or water of unknown quality.  
To eliminate a choking hazard for  
young children, remove and safely  
discard the protective cover fitted to the  
power plug of this appliance.  
Do not place the appliance directly  
against the wall. Ensure there is  
adequate airflow at the rear and sides  
by positioning the appliance 10cm  
away from the wall.  
ph: 0800 273 845 (New Zealand).  
Do not place the Breville Chill Control™  
near the edge of a bench or table during  
operation.  
If the supply cord is damaged, it must be  
replaced by the manufacturer, its service  
agent or similarly qualified person in  
order to avoid a hazard.  
Do not place the appliance on or near  
a hot gas burner, electric element or  
where it could touch a heated oven.  
Filter replacement is essential for the  
product to perform as represented and  
must be replaced every 8 weeks.  
Always turn the power Off and remove  
the plug before cleaning.  
For any maintenance other than  
cleaning, call Breville Customer Service  
on ph: 1300 139 798 (Australia) or  
ph: 0800 273 845 (New Zealand).  
Do not operate the appliance on a sink  
or drain board.  
Remove and empty the pre-filter tank  
before changing filter.  
Ensure that the surface is level, clean  
and free of water.  
This appliance has been designed to be  
used continuously.  
Consult a qualified electrician if  
the grounding instructions are not  
completely understood, or if doubt  
exists as to whether the appliance is  
properly grounded.  
The Breville Chill Control™ is not  
intended to be operated by means of  
an external timer or separate remote  
control system.  
Do not operate without a filter in place.  
Keep the appliance and accessories  
clean. Follow the Care and Cleaning  
instructions provided on Page 14.  
To protect against electric shock, do not  
immerse the power base, power cord or  
power plug in water or allow moisture  
to come in contact with these parts.  
WARNING  
Always switch the Breville Chill  
Never immerse the power base, power  
cord or power plug in water or allow  
moisture to come into contact with  
these parts.  
Control™ Off at the power outlet and  
unplug if the appliance is not in use,  
before cleaning, before attempting to  
move the appliance, disassembling,  
SAvE THESE  
INSTRUCTIONS  
 
4
5
KNOW yOUR BREvILLE CHILL CONTROL™  
KNOW  
G
H
I
your Breville Chill Control™  
A
B
C
D
E
F
A. 2 Litre Pre-Filter Water Tank  
B. 4 Litre Filtered Water Tank  
C. variable Temperature Slider  
D. LEd Indicator  
G. BRITAMemo - electronic cartridge  
exchange indicator  
H. BRITAMAXTRA Water Filter Cartridge  
I. Extra Tall Height For Bottles  
E. Water dispenser Lever  
F. 1 Litre Stainless Steel Cooling  
NOT SHOWN  
Reservoir  
Removable Plug - For easy cleaning  
Breville Assist™ Plug  
 
7
OPERATING yOUR BREvILLE CHILL CONTROL™  
3. Position the variable temperature slider  
BEFORE FIRST USE  
to the centre.  
OPERATING  
Before first use, remove and safely discard  
all promotional labels and packing materials  
attached to the Breville Chill Control™.  
4. Place a large container or jug under  
the spout.  
your Breville Chill Control™  
5. Press the dispenser lever until water  
reaches the MIN level, then discard  
remaining water.  
Remove the filter cartridge from the plastic  
packaging and keep in a safe place. Do not  
re-insert the filter until (a) flushing process  
and (b) preparation of filter cartridge has  
been completed (refer to page 10).  
6. Repeat this process with cold tap water  
twice and discard.  
Remove the lid, plastic plug and pre-filter  
tank and wash in warm soapy water. Rinse  
and wipe dry using new cloth. Wipe exterior  
of appliance with a soft damp cloth and  
dry thoroughly.  
7. Do not fill above the maximum level  
indicated.  
NOTE  
If the plastic plug is inserted while  
the cooling tank is empty, it will take  
approximately 7 minutes for the air to  
release from the cooling tank.  
During this time chilled water cannot  
be dispensed.  
Place the appliance on a dry, flat level  
surface. Plug into 230-240V outlet and  
turn power On.  
NOTE  
Do not place the appliance directly  
against the wall. Ensure there is  
adequate airflow both at the rear and  
sides by positioning the appliance  
10cm away from the wall.  
THE BRITAMAXTRA CARBON  
FILTRATION PROCESS  
Activated carbon reduces chlorine, metals  
such as lead, copper and limescale for  
cleaner, clearer better tasting water.  
FLUSHING THE BREvILLE  
CHILL CONTROL  
Leaves in flouride.  
PREPARING THE BRITAMAXTRA  
FILTER CARTRIdGE  
It is important that you flush and rinse out  
the dispensing system before using the  
appliance for the first time.  
1. Remove the filter cartridge from its  
Please note you should carry out these steps  
without the BRITAMAXTRA cartridge in  
place. Plug the appliance into an appropriate  
electrical outlet and switch On.  
wrapping.  
NOTE  
It is normal for the cartridge to  
appear moist when removed from its  
wrapping, this is simply condensation.  
1. Remove filter cartridge from the  
pre-filter tank and the removable plug  
from filter tank.  
2. Fill the pre-filter tank to the maximum  
level with water.  
 
9
OPERATING yOUR BREvILLE CHILL CONTROL™  
OPERATING yOUR BREvILLE CHILL CONTROL™  
2. Immerse the filter cartridge in cold  
water and agitate gently to remove  
any air bubbles.  
LEd INdICATOR  
The WHITE light will turn On first to  
indicate the appliance is in cooling mode.  
When the water inside the cooling reservoir  
has chilled (approximately 75 minutes )  
the LED indicator will change to BLUE.  
In warmer climates the time to chill will  
take longer.  
SETTING THE BRITA® MEMO  
NOTE  
Once you have fitted and prepared your  
filter cartridge, start the BRITAMemo  
as follows:  
We recommend you change the  
BRITAMAXTRA filter every 8 weeks.  
Replacement filters can be purchased  
through major retail outlets or via  
store.brita.com.au.  
1. Press and hold the START button until  
4 bars appear on the display and flash  
twice. The filter replacement reminder  
is now set.  
For additional questions on the  
BRITA replacement filters, please  
contact BRITA Consumer Service on  
1300 557 762.  
2. The flashing dot in the corner of the  
display indicates the filter replacement  
reminder is working.  
AdjUSTING THE WATER  
TEMPERATURE  
The variable temperature slider allows you  
to adjust the temperature of filtered water  
to suit your taste.  
The temperature of the water will vary  
depending on the selection made.  
Slide the lever to the far left for the coldest  
setting or to the right for room temperature  
filtered water.  
A selection in the middle will give you  
filtered water somewhere between chilled  
and room temperature.  
AUTO PROTECTION MOdE  
If there is an error with internal electronics  
or the fan is externally obstructed, the LED  
will start to flash, alternating between BLUE  
and WHITE and the appliance will enter  
into auto protection mode.  
To reset the appliance, unplug the unit from  
the power outlet, wait for a few minutes until  
the LED stops flashing, and plug back into  
power outlet.  
3. Insert the cartridge into the cartridge  
housing of the pre-filter tank and push  
firmly into place until it clicks into  
position.  
4. Take the pre-filter tank out of the water  
tank, fill it under the tap with cold tap  
water and allow it to filter through.  
Discard the first two fillings. They are  
used to flush the filter cartridge.  
If the LED continues to flash once reset,  
contact Breville Customer Service  
1300 139 798 for further assistance.  
5. Place the pre-filter tank back into the  
unit and refill with water. Ensure the  
water is always above the minimum  
level for optimum flow rate.  
3. At the end of every 2 weeks, 1 bar will  
disappear indicating the remaining  
cartridge life. Ensure you have a new  
replacement BRITAMAXTRA water  
filter cartridge available when only  
1 bar is showing.  
USING THE BRITA® MEMO  
6. The Breville Chill Control™ is now  
It is important to change your filter  
cartridge regularly to enjoy the benefits  
of filtered water.  
The BRITAMemo (electronic exchange  
indicator) reminds you when your filter  
cartridge needs to be changed. It is  
automatically calibrated according to  
average use of 1 litre of water per day  
and will remind you to change your filter  
every 8 weeks.  
ready for use.  
NOTE  
NOTE  
The LED indicator does not change  
colour when adjusting the variable  
temperature control slider.  
Repeat the above process every time  
you insert a new cartridge.  
7. Once the water has been filtered, the  
pre-filter tank can be refilled. Water will  
filter through as it dispensed into the  
filter tank water.  
NOTE  
If dispensing more than 1 litre of  
chilled water at one time, it will  
take approximately 75 minutes for  
another litre of water to be chilled to  
minimum temp.  
It will take 6 minutes on average to  
filter 1 litre of water through the  
BRITAMAXTRA cartridge.  
 
10  
11  
OPERATING yOUR BREvILLE CHILL CONTROL™  
4. All 4 bars will disappear and a flashing  
REMOvING THE FILTER CARTRIdGE  
arrow will appear to indicate the  
cartridge should be replaced after  
8 weeks.  
When it is time to replace the cartridge after  
8 weeks use, simply lift the ring pull handle  
on top of the cartridge to remove.  
The cartridge may be disposed of in  
household waste or you can contact the  
BRITAconsumer service for advice on  
Ph: 1300 557 762 for advice on recycling.  
More information on the use of BRITAfilter  
cartridge and the BRITAMemo can be  
found in the BRITAinformation Guide.  
5. Wash and dry the pre-filter tank, and  
insert a new cartridge (see Preparing  
the Filter Cartridge on page 10).  
6. To set the BRITAMemo, see  
instructions on page 11.  
NOTE  
The BRITAMemo is intended to  
be used only with BRITAfilter  
cartridges.  
 
12  
13  
CARE & CLEANING FOR yOUR BREvILLE CHILL CONTROL™  
CARE & CLEANING  
REMOvABLE PLASTIC PLUG  
CARE & CLEANING  
1. Switch the appliance Off and unplug  
the power cord from the power outlet  
before cleaning.  
The Breville Chill Control™ includes a  
removable plastic plug that separates  
filtered from chilled water. As well as  
making the cleaning of the cooling  
reservoir easy, it assists in the cooling  
process to keep the water cool.  
for your Breville Chill Control™  
2. Remove the lid, pre-filter tank and  
water from the filter tank.  
3. To empty the stainless steel cooling  
reservoir, remove the plastic plug that  
separates the filtered water from the  
cooling reservoir.  
The plastic plug can be dismantled for  
cleaning. Simply squeeze the sides to  
release as shown below and wash with  
warm soapy water.  
4. Turn the appliance upside down to  
drain any remaining water from the  
cooling reservoir.  
5. Wipe the inside of the filter tank  
and cooling reservoir with a clean,  
damp cloth.  
6. Wash the lid, pre-filter tank and plastic  
plug in warm soapy water using a mild  
detergent and dry thoroughly.  
7. Wipe exterior of appliance with a soft,  
damp cloth.  
STORAGE  
8. Do not immerse the base in water or  
Ensure the Breville Chill Control™ is  
switched Off, all internal tanks are  
emptied of water and it is clean and dry  
before storing.  
any other liquid  
Stand the Breville Chill Control™ upright  
on the power base. Do not store anything  
on top.  
Flush the appliance again before using  
again (see instructions on page 9)  
NOTE  
Do not use alkaline or abrasive  
cleaning agents, steel wool or  
scouring pads as these can damage  
the surface of the appliance.  
Do not place any part of this appliance  
in a dishwasher.  
 
15  
TROUBLESHOOTING  
PROBLEM  
POSSIBLE CAUSES  
WHAT TO dO  
TROUBLESHOOTING  
Filtered water not cold  
enough  
Water chiller positioned  
in direct sunlight  
Move water chiller away  
from direct sunlight.  
High ambient  
conditions (30˚C +)  
In warmer conditions,  
the time to chill will  
take longer.  
Water Chiller too close  
to wall  
Position water chiller  
min 10cm clearance away  
from walls.  
Water Chiller has not  
been switched ON long  
enough.  
Wait approximately  
75 minutes after filling  
with tap water.  
After filling-up 1 litre  
water bottle, water is not  
cold anymore  
Chilling tank capacity  
is approximately 1 litre.  
It takes approximately  
75 minutes to chill  
1 litre water from  
Wait approximately  
75 minutes after  
dispensing large  
amount of chilled water.  
room temperature.  
Fan too noisy/does not  
switch off  
High ambient  
In warmer conditions,  
the time to chill will  
take longer.  
conditions (30˚C +)  
Unit is running in  
high power mode  
How do I know the water  
has chilled?  
The LED light will switch  
from WHITE to BLUE.  
LEd not switching from  
WHITE to BLUE  
Initial water  
temperature in chill  
tank is too high  
Move water chiller away  
from direct sunlight.  
High ambient  
conditions (30˚C +)  
In warmer conditions,  
the time to chill will  
take longer.  
Water Chiller too close  
to wall  
Position water chiller  
min 10cm clearance away  
from walls.  
Water Chiller has not  
been switched ON  
long enough  
Wait approximately  
75 minutes after filling  
with tap water.  
 
17  
TROUBLESHOOTING  
PROBLEM  
NOTES  
POSSIBLE CAUSES  
WHAT TO dO  
LEd indicator flashing  
& alternating between  
WHITE & BLUE  
Water Chiller is in Auto  
Protection Mode  
Fan externally obstructed  
or an error with the internal  
electronics.  
Unplug the unit & wait a  
few minutes to reset the  
unit.  
If problem persists call  
Breville Customer Service  
1300 139 798  
Water does not flow  
during initial flushing  
Air lock in internal  
tubing  
With the chilling chamber  
full, move slider to the  
middle position and  
use the plug like a sink  
plunger while holding the  
dispensing paddle open to  
clear the air lock.  
Flow rate of water slow  
Not enough water in  
water tank  
Ensure the water level is  
always above the MIN level  
for optimum flow rate.  
Water tank has small  
dark particles  
Brita filter cartridge  
& unit have not been  
flushed  
Immerse the filter cartridge  
in cold water and agitate to  
remove air bubbles.  
Flush the unit twice before  
each new cartridge.  
How can I clean the  
chilling chamber  
Remove the plastic plug in  
the filter tank to clean the  
chilling chamber.  
There is a flashing arrow  
& no bars appearing on  
the Brita Memo indicator  
The Brita Filter  
cartridge may need  
to be replaced  
Brita Filter Cartridge  
should be replaced every  
8 weeks.  
What does the Brita Filter  
cartridge remove from  
the water?  
The Brita Filter reduces  
chlorine, metals such as  
lead, copper, & limescale.  
Leaves in flouride.  
Where can I purchase the  
Brita Filter cartridges  
Brita filter cartidges are  
available at all leading  
retailers or contact Brita  
Consumer Service  
Ph: 1300 557 762  
 
18  
19  

Bosch Appliances Range HGS5053UC User Manual
Bosch Power Tools Power Hammer 11222EVSG User Manual
Cabletron Systems Switch HSIM W87 User Manual
Califone Cassette Player CAS1500 User Manual
Canon Photo Printer 3295B002 User Manual
Carrier Heat Pump 38AYB User Manual
Casio Blood Pressure Monitor BP 1MY 1 User Manual
Chauvet Work Light Aw 7x7 User Manual
Chicago Electric Staple Gun 67256 User Manual
Chicago Pneumatic Air Compressor CPVS 40 User Manual